For most ice fishing, a light line matched to your target fish and a knot that suits it matter more than the brand. Berkley NanoFil is a thin, low-stretch line that many ice anglers like for sensitivity, but it is not braid or monofilament, and some knots that work on braid will not hold in it. Use a Palomar or a double uni knot with NanoFil. The snell knot is a separate tool, used for tying hooks to the line on tip-ups, quick-strike rigs, and dropper chains.
What Berkley NanoFil is
NanoFil is a “uni-filament” line made from gel-spun polyethylene. It is thin, has almost no stretch, and has little memory, which helps it lie flat on the spool. It is neither braid nor mono. Colors include Clear Mist, Hi-Vis Chartreuse, and Lo-Vis Green, and ice anglers commonly use it in the 2 to 6 pound range.
Availability has been uneven, and the line may be discontinued in some sizes or colors. Check current stock before you plan a whole season around it.
Because NanoFil has no stretch, it transmits light bites well but leaves no cushion. Set your drag light, roughly one-quarter to one-third of the line’s test strength, so a sudden run does not snap the line.
Knots that hold in NanoFil
Berkley recommends the Palomar and the double uni for NanoFil. The improved clinch, which works well on monofilament, tends to slip on this smooth, thin line. If you are switching from mono, retie your connections with one of the recommended knots and test them before you fish.
Adding a leader for panfish
NanoFil is highly visible in clear water, so many anglers add a short leader. A 2 to 4 foot fluorocarbon leader, in about 1 to 4 pound test for panfish, joins to the NanoFil with a double uni or a small swivel. Fluorocarbon is less visible than NanoFil in clear water, but it is not invisible, so keep leaders short and fish them lightly.
How to tie a snell knot
The snell knot is a simple way to tie a hook to the line so the point pulls toward the fish on the hookset. It works on hooks with an up-turned or down-turned eye.
- Pass the line through the hook eye, leaving a tag end along the shank.
- Lay the tag end along the hook shank and form a small loop.
- Wrap the loop around the shank and the standing line, working toward the eye. Five to ten wraps are typical, and about seven is common.
- Pull the standing line to tighten the wraps, then trim the tag end.
Because step-by-step descriptions can be hard to follow, watch a demonstration video before you tie your first one. Keep the wraps neat and close together. More wraps are not always stronger. Past about seven or eight turns on fine line, the line can cut itself.
Where a snell fits on the ice
Snell knots show up on several ice rigs:
- Tip-ups with live bait. A snell on a hook lets the hook sit straight and lets the bait swim naturally.
- Quick-strike rigs. The snell and the rig’s hooks sit together so the fish is hooked quickly.
- Dead-bait rigs. Dead smelt or herring can be fished on a snell-tied hook.
- Dropper chains below a spoon. A snell hook on a short dropper can add a second bait.
For the tip-up side of the setup, see our guide to setting up a tip-up for ice fishing.
Other core ice knots
You will also use a few other knots on the ice:
- Palomar: a strong, simple knot for braid and superline, and a recommended choice for NanoFil.
- Improved clinch: works well on monofilament, usually with five to seven turns.
- Trilene and uni knots: used for tying hooks and lures on mono or fluorocarbon.
- Double uni and FG: used to join line to leader.
Moisten every knot before you cinch it down. This reduces friction and helps prevent heat damage. Retie after a big fish, or any time you see frays.
Line in the cold
Monofilament stiffens and coils in the cold, so it is harder to handle with cold fingers. Ice-specific monofilament and fluorocarbon hold up better. Braid and superline can soak up water, and that water can ice up in rod guides in subzero air. Keep line wet below the surface when you can, since ice forming on the line at the hole can snap light line.
If you are fishing from a shelter or from a heated spot, these issues are smaller. Out in open wind, plan on more frequent checks.
Common mistakes
- Using the wrong knot on NanoFil. Test your knots, since some that work on mono slip on it.
- Assuming NanoFil is braid. It is a uni-filament, not a braid or fused line, and braid knots do not all hold.
- Overwrapping a snell. Extra wraps do not add strength on fine line.
- Overfilling or overtightening. Light, lightly set drag is the right starting point.
Packing out and safety
Clip tag ends close and pack out any line scraps. Line left on the ice can tangle wildlife. For the rest of your gear list and ice checks, see our ice fishing gear and technology overview. For a rod to pair with your line, see our rod and reel combo guide.