Gear and Electronics

How to Set Up a Tip-Up for Ice Fishing

Set up a tip-up for ice fishing step by step: spool the line, find depth, bait the hook, set the trip, and place the tip-up so the flag signals a bite.

On this page
  1. What a tip-up does
  2. What you need before you start
  3. Step 1: Spool the line and tie the leader
  4. Step 2: Find the depth and set bait height
  5. Step 3: Bait the hook
  6. Step 4: Set the trip and flag
  7. Step 5: Set the tip-up on the hole
  8. Setting for walleye vs pike
  9. Common mistakes
  10. Rules and safety

To set up a tip-up, spool the line, tie on a leader, find the bottom, raise your bait to the right height, bait the hook, set the trip, and place the tip-up over the hole so the spool turns freely. The steps are simple. The numbers below are starting points, so adjust them for the fish you are targeting and the conditions on the day.

What a tip-up does

A tip-up holds a line passively in the hole. The line runs over a spool, and the spool is held by a trip bar. When a fish takes the bait and pulls line, the spool turns, releases the trip, and a spring-loaded flag pops up. You then lift the tip-up out of the hole and land the fish by hand. That makes a tip-up a good companion for a rod you jig in a nearby hole.

What you need before you start

  • A tip-up, either a cross-frame model or a round thermal model that covers the hole
  • Backing line: 50 to 100 yards of 20 to 50 pound braided Dacron
  • A 2 to 4 foot fluorocarbon leader
  • A small barrel swivel to join the backing and the leader
  • Hooks suited to your target fish
  • Split shot and a depth finder or sonar
  • Live bait, if you are using it
  • A way to mark depth, such as a bobber stop

Avoid monofilament for backing. It coils and freezes more easily than braided Dacron.

Step 1: Spool the line and tie the leader

Spool the backing onto the tip-up’s spool. Tie the barrel swivel to the end of the backing, then attach the leader to the other side of the swivel.

Leader strength depends on the fish. For walleye, a 6 to 12 pound fluorocarbon leader is a common starting point. For pike, use a heavier leader, 20 to 40 pound fluorocarbon, or a light wire leader, since pike can cut lighter line. Our ice fishing line and knots guide covers the knots you will need for the swivel and the leader.

Step 2: Find the depth and set bait height

Clip a depth finder or a small weight to the hook, and lower it until the spool stops turning. That tells you the bottom is reached. Then raise the line so the bait sits at the height you want. Mark the spot with a bobber stop or by noting where the line meets the frame, then remove the weight.

Step 3: Bait the hook

For walleye, a fathead or shiner works well, hooked through the back or lips so it stays lively. For pike, use a 4 to 8 inch sucker or shiner, or dead smelt or herring on a quick-strike rig.

Add a split shot 12 to 18 inches above the hook to keep the bait in the strike zone.

Hook choice depends on the rig:

  • Walleye: a #4 to #8 octopus hook, or a #10 to #12 treble.
  • Pike: a quick-strike rig with two trebles, about #4 to #8, or a single circle hook.

Step 4: Set the trip and flag

Bend the flag down and hook it under the trip on the spool. Most tip-ups have a light and a heavy setting:

  • Light setting for small baits and light bites.
  • Heavy setting for large, active baits that might trip the flag on their own, or in windy conditions.

Keep in mind that wind can trip a flag, so a raised flag does not always mean a fish.

Step 5: Set the tip-up on the hole

Lower the rig into the hole and center the spool so the line does not rub on the ice edge. Make sure the spool spins freely. Thermal models use a sealed, lubricated shaft, so follow the maker’s maintenance guidance.

In cold weather, pack snow around the base or cover the hole to slow freezing and block light. Light can spook some fish.

Setting for walleye vs pike

The timing of the hookset differs for the two rigs:

  • Conventional rig with live bait: wait until the spool spins, then set the hook.
  • Quick-strike rig: set right away, so the fish does not swallow the hook deeply. Waiting can cause deep hooking.

When you reach a flag, lift the tip-up out of the hole, set it aside, and bring the fish in hand over hand. You can feel the head shakes and runs directly through the line.

Common mistakes

  • Using monofilament backing. Braided Dacron handles cold better.
  • Waiting too long on a quick-strike rig. Set right away.
  • Assuming every flag is a fish. Wind can trip a flag.
  • Setting the bait too close to the bottom for pike. Pike often hold higher, near weeds or mid-depth.

Rules and safety

Tip-up rules vary by state and province. Many areas require a name and address on each tip-up and require you to keep them within sight. Check your local regulations before you set lines, including limits on the number of lines.

Watch your footing when you run to a flag, especially on glare ice. For ice checks and the rest of your gear list, see our ice fishing gear and technology overview. For bait choices, see our guide to the best bait for ice fishing.

The complete guide to gear and electronics

Ice Fishing Gear and Technology: Sonar, Rods, Line and Power
Read the guide

Keep exploring

Guides from other topics

All topics →