Fishing sonar works by sending a pulse of sound into the water and listening for the echoes that bounce back. A transducer converts an electrical pulse into a sound wave, then turns the returning echoes back into electrical signals. The unit uses the time each echo takes to return to work out depth, and the strength of each echo to show hard and soft bottoms, and fish. It then draws the results on screen.
How a sonar sends and receives a pulse
The transducer contains a piezoelectric element. When the unit sends a pulse, the element converts electrical energy into a sound wave and sends it down in a cone-shaped beam. The sound bounces off anything in its path, including the bottom, weeds, rock, and fish. The same element picks up the returning echoes and converts them back into electrical signals for the display.
Modern units repeat this process many times per second, which is why the screen can show a near-continuous picture of what is below the transducer.
Working out depth from echo time
Sound travels about 4,800 feet per second (about 1,500 meters per second) in water, which is roughly 4.3 times faster than in air. Because the pulse goes down and comes back, the unit uses this formula:
Distance = (speed of sound × echo time) ÷ 2
Here is a worked example. A fish 10 feet below the transducer sends back an echo in about 4 milliseconds. Twice the distance is about 6.1 meters, and dividing by 1,500 meters per second gives a time of about 0.004 seconds. The unit does this calculation for every echo it receives.
Frequency: why it changes the picture
Sonar uses different frequencies, and each one trades detail for depth:
- Lower frequencies, such as 50 kHz or 83 kHz, have a wider beam and reach deeper water, with less fine detail.
- Higher frequencies, such as 200 kHz, have a narrower beam, show more detail, and work best in shallower water.
Some units use CHIRP, which sweeps a range of frequencies rather than sending one. This helps separate close targets, such as your jig and a fish near it. Down and side imaging use higher frequencies still, and live forward-facing sonar uses phased arrays that build real-time images. For a comparison of the main sonar types, see our overview of the best sonar for ice fishing.
Cone angle and how much area the sonar covers
Sonar does not see the whole lake. It covers only the area inside its beam or cone. A 20-degree cone covers a circle about 0.35 times the depth across. At 10 feet, that is roughly a 3.5-foot circle. A narrower cone covers less area, but it gives a more focused view.
The displayed depth is the distance from the transducer to the target. A fish near the edge of the cone can look deeper than it really is, because the echo travels farther. That is one reason to watch the target as it moves through the beam.
Hard and soft bottoms, and fish
Echo strength tells you about what the sound hit. Hard bottoms, such as rock or gravel, return stronger echoes. Hard bottoms often also return a second, weaker echo at twice the depth, which is a useful clue. Soft mud absorbs more of the sound and returns weaker echoes.
A fish’s air-filled swim bladder returns a strong echo, which is why fish stand out on a screen. Gain controls how weak an echo can be and still show. Turning gain up shows more faint returns, but it can also add clutter.
Why fish appear as arches
On a scrolling sonar, a fish often appears as an arch. As your boat or position moves, the fish passes through the cone. Its distance from the transducer shrinks as it enters the center and grows again as it leaves. That change in distance draws an arch on the screen.
An arch is not the fish’s shape. It reflects movement through the cone. A bigger arch does not reliably mean a bigger fish. If the sonar is stationary, a fish may show as a flat or long line.
What the screen cannot tell you
A sonar screen is a useful tool, but it has limits:
- It does not show the whole lake. Only the cone or beam footprint is covered.
- An arch is not a fish’s shape.
- A bigger arch does not mean a bigger fish.
- It cannot measure ice thickness. Test the ice yourself with a drill or an ice chisel.
Sound from sonar is not known to scare most fish at normal settings, but the evidence on this is limited.
How ice fishing changes things
On the ice, the transducer hangs in the hole, so the cone points straight down the hole. A flasher shows the returns on a rotating dial in real time, which suits stationary ice fishing well. A digital unit adds a scrolling history, which is useful for seeing the bottom as you move between holes. For a side-by-side comparison, see our flasher vs fish finder guide.
For live forward-facing sonar and how it differs from these standard types, see our Garmin Panoptix guide. For the rest of the gear list, see our ice fishing gear and technology overview.